Pianos consistently make movers yearly list of products that are most often damaged. Grand pianos are particularly troublesome. Practicing the following procedures for disassembling, padding and loading grand pianos will prevent damage, lower claims expenditure, and enhance client complete satisfaction.
1) At least three people are required to deal with a baby grand piano. If the baby grand piano needs to increase or down stairs or if a full or concert grand piano requires to be transferred, a minimum of four people are required.
2) Always finish a precise and extensive inventory. It might be needed or preferable to use a visual inventory to effectively explain and show pre-existing damage.
3) As numerous parts are taken apart, please location all hardware in an appropriately labeled parts bag and after that position the parts bag in a "Parts Box".
4) Get rid of the music rack (lyre) from its track by pulling it toward the keyboard. Wrap it in a clean furnishings pad.
5) Disconnect the lid by removing the hinge pins. Wrap the lid in a clean furniture pad.
6) Eliminate the prop that holds the lid open and cover it in a tidy furnishings pad. The prop has a hinge pin and remains in 2 pieces.
7) Remove the pedal assembly and wrap it in a clean furniture pad. The braces at the rear of the assembly rest in slots at each end. When removing the screws, please take care not to drop the braces. In addition, please be especially cautious with the push-rods so that they will not get bent. As you face the piano, number the push-rods from left to right as "1", "2", and "3", by placing a piece of masking tape with the appropriate number on each rod. Keep in mind: If masking tape is not available, please use properly identified parts bags for this function. When reassembling at location, please make certain to put the rods in the right order so that the pedals will work appropriately.
8) Pad the piano by positioning a tidy rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the cover of the keyboard to avoid it from flopping open while you manage the piano. Cover the top of the piano with two clean furnishings pads, neatly folded around the keyboard. Usage elastic band to secure the pads. Keep in mind: Please guarantee that the surface area of the piano is dust-free before padding it. Padding a highly polished surface area that is dusty might trigger fine scratches, specifically on a black lacquer finish.
9) this contact form Position a piano board and connect the straps so that it is ready to receive the piano. The raised brace on the piano board must be at the keyboard end of the piano.
10) Remove the left front leg by positioning someone below the piano at the left end of the keyboard. The other 2 people should support the left front corner. The person beneath the piano should turn the maintaining block so that the long end points away from the leg. The screws, if there are any, should then be eliminated. The "beneath" person ought to then get out from under the piano before actually removing the leg. Be sure to have two individuals raising the corner of the piano while the third person gets rid of the leg. Keep in mind: Please make certain to keep in mind which legs were eliminated from which positions considering that some pianos have legs that are not interchangeable.
11) Location the piano on the piano board by reducing the "leg-less" end onto the board. Please be sure to raise the entire piano slightly while finishing this maneuver to prevent unnecessary pressure on the remaining, attached legs as the piano ideas. Be sure that the piano is focused snugly against the brace at the end of the piano board.
12) Eliminate the 2 remaining legs and wrap them in clean furnishings pads. These legs are kept in location by a This Site "crucial and slot" arrangement. To remove the leg, slide it inward towards the center of the piano till it comes out of the slot.
13) Protect the piano to the piano board by bringing the ends of the straps together and fastening them. Place folded burlap pads over the furniture pads but under the straps to supply additional security to the edges of the piano. To prevent the strap near the narrow end of the piano from slipping off, tie the loose ends of the two straps together.
14) To move the piano over a flat, level surface, tilt the piano and piano board and place a four-wheel dolly under the center of the piano board.
15) To move the piano up or down stairs, use the piano board as a skid. After adequately padding the stairs for security versus home damage, place the keyboard end of the piano toward the bottom of the stairs. Connect a bulge strap to the top end of the piano board to prevent the piano from slipping.
16) To fill the piano, leave it on the piano board and location it in a tier as the first base item with the keyboard facing the wall of the preceding tier. The finest location to pack the padded cover is between the piano and the preceding tier or between the piano see this and the wall.
Although grand pianos represent a significant challenge, they can be moved without damage by utilizing common sense and practicing the procedures noted above.